Update: Discontinued; Use Part: 36510
The Moto-Massage is a jet that automatically travels up and down to massage a person’s back. The mixing of air and water in a jet, along with a playable spine causes the sweeping motion of the Moto-Massage. The intensity and speed of the Moto-Massage can be adjusted with the air control valve. The Moto-Massage is curved to fit the curvature of the back.
The Moto-Massage consists of a jet nozzle, water tube, threaded fitting, vertebra and an air tube with an o-ring. The Moto-Massage is held in place by a special recess behind the spa shell. A shim is used to assist in proper movement of the Moto-Massage.
Compatible with 2004 to 2008 Hot Spring Highlife spa models.
*Check specs section for full list of compatible models and years.
Specifications
| Item |
|
Part Number |
| 1a |
Facia Plate Duel Moto Cool Grey |
73537 |
| 1b |
Facia Plate Duel Moto Warm Grey |
73538 |
| 2 |
screw 10-16 |
34366 |
| 3a |
screw cover cool grey |
36510 |
| 3b |
screw cover warm grey |
73306 |
| 4 |
duel moto jet warm grey |
73542 |
| 5 |
air tube w/ oring |
73539 |
| 6 |
abrasion cap |
30723 |
| 7 |
o ring Moto air tube |
33020 |
| 8 |
Niche Air fittting (buy assembly) |
73540 |
| 9 |
Manifold w/ airline assembly |
73540 |
| ** |
Check Valve |
38390 |
| Removal |
- Open or remove the spa cover.
- Using a standard blade screwdriver, remove the three faceplate screw covers.
- Remove the three screws securing the Moto Massage faceplate to the spa.
- Remove the Moto Massage faceplate.
- Reach into the jet recess and locate the air tube. Gently remove this tube from the barbed nipple at the back of the recess.
- Grasping the base of the Moto Massage (end closest to the rear of the jet recess) gently turn the entire assembly counterclockwise until it can be removed.
- To reinstall the Moto Massage, reverse steps 1 to 6.
Important Instructions Regarding Moto Massage Alignment:
In order the for the Moto Massage to operate properly it is imperative that the Moto Massage nozzle be properly positioned after the assembly is tightened in the Moto niche.
To properly align, ensure that the two holes located on the nozzle face are position horizontally and that the Moto assembly travels vertically within the niche.
|
|
The following are the major causes of Moto-Massage failure;
- Shim misaligned.
- Low Water flow due to jet pump malfunction or dirty, clogged filters.
- No or improper air mixture due to air valve failure, air line disconnected, frozen air lines, or non-operative check valves.
- Moto-Massage nozzle misaligned
|
| |
| Specifications: |
|
(back to top)
|
| |
| Removal |
- Open or remove the spa cover.
- Using a standard blade screwdriver, remove the three faceplate screw covers.
- Remove the three screws securing the Moto Massage faceplate to the spa.
- Remove the Moto Massage faceplate.
- Reach into the jet recess and locate the air tube. Gently remove this tube from the barbed nipple at the back of the recess.
- Grasping the base of the Moto Massage (end closest to the rear of the jet recess) gently turn the entire assembly counterclockwise until it can be removed.
- To reinstall the Moto Massage, reverse steps 1 to 6.
Important Instructions Regarding Moto Massage Alignment:
In order the for the Moto Massage to operate properly it is imperative that the Moto Massage nozzle be properly positioned after the assembly is tightened in the Moto niche.
To properly align, ensure that the two holes located on the nozzle face are position horizontally and that the Moto assembly travels vertically within the niche.
|
| Item |
|
Part Number |
| 1a |
Facia Plate Moto White |
36079 |
| 1b |
Facia Plate Moto C Grey |
36511 |
| 1c |
Facia Plate Moto W Grey |
73305 |
| 2 |
Screw 16×3 |
34366 |
| 3a |
Screw Cover Moto White |
36144 |
| 3b |
Scrrew Cover Moto c grey |
36510 |
| 3c |
Screw Cover Moto w grey |
73306 |
| 3d |
Screw Cover Taupe |
71896 |
| 4 |
Moto Jet Assembly white |
73307 |
| 5 |
Air Tube with o oring |
70307 |
| 6 |
Abraision cap (air tube) |
30723 |
| 7 |
O ring moto air tube |
33020 |
| 8a |
Extrusion shim MM Short |
36143 |
| 8b |
Extrusion shim MM Long |
36557 |
| * |
Check Valve |
38390
|
* Non Illustrated Part
| Removal |
- Open or remove the spa cover.
- Using a standard blade screwdriver, remove the three faceplate screw covers.
- Remove the three screws securing the Moto Massage faceplate to the spa.
- Remove the Moto Massage faceplate.
- Reach into the jet recess and locate the air tube. Gently remove this tube from the barbed nipple at the back of the recess.
- Grasping the base of the Moto Massage (end closest to the rear of the jet recess) gently turn the entire assembly counterclockwise until it can be removed.
- To reinstall the Moto Massage, reverse steps 1 to 6.
Important Instructions Regarding Moto Massage Alignment:
In order the for the Moto Massage to operate properly it is imperative that the Moto Massage nozzle be properly positioned after the assembly is tightened in the Moto niche.
To properly align, ensure that the two holes located on the nozzle face are position horizontally and that the Moto assembly travels vertically within the niche.
|
|
Reviews
There are no reviews yet.